3" Slide Valve with Gate Seals
Item No. 6382
3" Slide Valve with Gate Seals is rated
out of
5 by
19.
Images
Video(s)
Details
https://www.campingworld.com/3quot%3B-slide-valve-with-gate-seals-6382.html
3" Slide Valve with Gate Seals
$12.25
$19.99
Save $7.74
(
39% Off
)
Additional Information
Features
The Valterra 3" Slide Valve with Gate Seals is made with tough ABS plastic. Shaft has been constructed from stainless steel and gives you an extra strong gate/shaft connection.
• Eliminate separation problems
• Includes seals, nuts, bolts, and threaded handle
Show moreShow less
• Eliminate separation problems
• Includes seals, nuts, bolts, and threaded handle
- Made with tough ABS plastic
- stainless steel shaft
- Extra strong gate/shaft connection
- Includes seals, nuts, bolts, and threaded handle
- Easy to operate
Specs
| Unit Weight | 0.80 lb |
|---|---|
| Brand | Valterra |
| MFG Part No. | T1003VPM |
Reviews
Q & A
The Valterra 3" Slide Valve with Gate Seals is made with tough ABS plastic. Shaft has been constructed from stainless steel and gives you an extra strong gate/shaft connection.
• Eliminate separation problems
• Includes seals, nuts, bolts, and threaded handle
Show moreShow less
• Eliminate separation problems
• Includes seals, nuts, bolts, and threaded handle
- Made with tough ABS plastic
- stainless steel shaft
- Extra strong gate/shaft connection
- Includes seals, nuts, bolts, and threaded handle
- Easy to operate
| Unit Weight | 0.80 lb |
|---|---|
| Brand | Valterra |
| MFG Part No. | T1003VPM |
Rated 3 out of
5
by
Robert Perker from
Black tank valve
Sure wish that once in 10 yrs the replacement of this valve would be called for. It's been
3 yrs since I've done this task. The valve I replaced became too hard for my wife to open
and close. The new valve solved this problem. With the passage of time it became
hard to open and close this new valve. I tried dumping in vegetable oil and operating
the valve to lubricate it but the valve remained difficult to operate. Three years latter I find
myself ordering another valve. What can I say... Camping World is blameless, they
shipped promptly. These valves won't last forever... Wish I don't have to do this job
another time in the future.
Date published: 2012-02-10
Rated 4 out of
5
by
Jerry Hyder from
Valterra Slide Valve
Valve works fine but the install instructions are lacking. I installed one valve, easy to
install but it leaked in a few days. Took it to a repair shop and had to buy a new valve
and had them install it. Few days later it starting leaking again. Ordered another valve
and installed it myself. After spending 30 minutes trying to install the seals on the waste
pipes, I discover I was trying to install them as they were in the package. This is wrong,
you have to reverse the seals from the way they come in the package. I checked the
instructions several times and no where does it say how the seals show face to be
installed. My professional installer had them reversed also. Need to explain how the
seals face when installing them.
Date published: 2014-09-19
Rated 5 out of
5
by
B Frank from
3 Valve, EZ to replace
This pretty much sums it up. When I bought my Class C Sportsman a
few years ago the waste valves were stuck so much that I was glad
that the tanks were empty, when I switched over. Anyways, the 3 took
about a half hour to replace, while also replacing the seals as well.
Very EZ to install, just reverse as taking the old one out! After two
years of owning the RV, they still worked like brand new, the pull never
leaked or stuck! I recommend these to anyone who is just replacing
with OEM, make shift. CHEAP & RELIABLE!
Date published: 2007-10-28
Rated 5 out of
5
by
Serge Ouellet from
Replacing an old slide valve
The existing slide valve had started to leak and rust was evident on one of the retaining bolts. The removal of the old valve went well and revealed that both rubber rings were in disrepair. Once I cleaned the pipes, the install of the new slide valve went extremely quick and easy. I particularly like the fact that the valve came with new bolts and non-slip nuts. The valve is obviously more solid than its predecessor and works like a charm. Very good product, highly recommended.
Date published: 2014-12-15
Rated 1 out of
5
by
James Ellsworth from
Valterra 3" blade valve
WARNING check your valve before installing; my slide did not fit snugly in valve body. It has a 1/2 inch gap top and bottom. I had installed vale but when I looked at installation the handle did not go tight against the stop. Thought maybe a gasket was not installed correctly so I pulled unit back off. Thats when I notice the gaps top and bottom on the slide gate. Holding unit horizontal, poured water on valved and it leaked like a sieve Checked this against the old valve and the seal was tight on that one. So cleaned and lubricated the old one and re-installed. I can imagine what would have happened had I not found this defect and the first time I took off the cap to empty the black tank, I would have gotten about two quarts of liquid crap all over myself Be carefull with any Valterra units, mine was made in Mexico. I had purchased the 1 1/2 inch valve also. that one was ok so installed and it works fine.
Date published: 2018-08-21
Rated 4 out of
5
by
Anonymous from
Flush King valve replacement
My valve was sticky and hard to open. I broke the handle one day
dumping the black water. I replaced the valve with this one and saved $35.00 since I
didn't have to buy the same kind I had before!
Date published: 2014-04-23
Rated 3 out of
5
by
kevin DeLawyer from
easy to install
I bought this product because my old valve was leaking. Installed this one it was easy did it in about 10 minutes.
after installing it I'm still having leaking issues. so I'm not sure.
Date published: 2012-08-29
Rated 5 out of
5
by
colochoclab from
Excellent product!
When my old valve started to leak, I was nervous about putting in a
new one. No worries! Super simple to replace and the new one works
so much better!
Date published: 2008-07-14
Do you have this valve with a long cable pull handle? If so, in what lengths is the cable?
My 5th wheel has black gate valve about 5 ft from control compartment where handles are accessed.
We do carry a 3" valve gate with 72" actuator cable plus hardware as SKU#55233. A 1.5" valve gate with 72" cable plus hardware we have listed as SKU#55232.<p>Replacement 96" and 120" cables with handle are also available from <a href=http://www.valterra.com/product-category/rv-products/aftermarket/sewer-sanitation/cable-actuated-waste-valve-kit/>Valterra</a>.
Date published: 2019-03-08
Which side of the seal faces out?
The raised side that is the smaller diameter faces outwards. <a href=https://youtu.be/UKSHnWhpMf0>Valterra RV Waste Valves</a>
Date published: 2019-03-08
Does this fit on 1 1/2 in sewer line?
I have the same product on my camper now and by my stupidity broke it. My line is 1 1/2 but this says 3. Will it work?
No
Date published: 2019-03-08
Can the handle be removed?
Can the handle be removed?
Yes, the handle is threaded.
Date published: 2019-03-08
can you just buy the seals?
<a href=http://www.valterra.com/product-category/rv-products/aftermarket/sewer-sanitation/bladex-valve-seals/>Valterra</a> does package just replacement seals, we unfortunately do not carry them only the complete slide valve with seals.
Date published: 2019-03-08
CAN T HANDLE BE REMOVED AND REPLACED ONTO SHAFT
Yes, the T handle is removable.
Date published: 2019-03-08
I have a 3inch grentec valve, will this one replace it?
what i am asking is will this new valve work with the flanges off the grentec brand?
This valve is interchangeable with Valterra, Grentec, Anonda, Larden, and Bristol valves.
Date published: 2019-03-08