Brass Water Heater Drain Valve, 1/2”
Item No. 6315
Brass Water Heater Drain Valve, 1/2” is rated
out of
5 by
7.
Images
Details
https://www.campingworld.com/brass-water-heater-drain-valve-12-6315.html
Brass Water Heater Drain Valve, 1/2”
$4.59
$7.99
Save $3.40
(
43% Off
)
Additional Information
Features
Replace water heater valves with sturdy, easily-installed brass replacements that allow easy draining of water tank.
Just twist the petcock to open valve for draining—no need to remove entire valve assembly.
Show moreShow less
Just twist the petcock to open valve for draining—no need to remove entire valve assembly.
Specs
| Unit Weight | 0.15 lb |
|---|---|
| Brand | Camco |
| MFG Part No. | 11703 |
WARNING: This product can expose you to chemicals including Lead (E/F), which is [are] known to the State of California to cause cancer and Lead (E/F) which is [are] known to the State of California to cause birth defects or other reproductive harm.
For more information, go to www.P65Warnings.ca.gov/product.
Reviews
Rated 5 out of
5
by
Nelson Durgin from
Making Life Easier
Does just what it is supposed to do. I have been dealing with the plastic plug for two
years. It was starting to leak and the head was getting pretty torn up. I was going to
invest in the replacement kit with wrench. This was going to include a new plastic plug,
and I figured I was going to be replacing this about every three years. It was also going
to cost an extra $5. The brass drain valve seems to work perfectly. Make sure you order
the correct size, and you will need plumbers teflon tape. I used a socket to install the
outer piece to the tank and then added teflon tape to the inner threads also. Seems to
be working fine, and hopefully it will cut down my winterization time by about 20 minutes
Date published: 2014-08-14
Rated 4 out of
5
by
JerryL1042 from
Brass water heater drain valve , 1/2
Removed old plug, flushed and cleaned tank, have not installed new drain plug yet because RV is winterized right now. Have new brass water heater drain plug valve 1/2 & Teflon tape ready to install it if we head south for the winter.
Date published: 2014-11-11
Rated 3 out of
5
by
colochoclab from
Not Bad
I wanted to install a drain valve for quite some time to replace the old nylon plug. This item works well, but I needed a lot of pipe tape on the smaller threads to stop the dripping. A little patience and it now works
good.
Date published: 2010-04-29
Rated 5 out of
5
by
DaveN from
Easy to install
Easily installed using socket wrench. Used PTFE tape on threads to prevent leaks. Better than removing and replacing plastic plugs every year.
Date published: 2019-10-23
Rated 4 out of
5
by
Anthony Robitzsch from
Drain Valve
A must-have in my book since the water heater manufactuer's don't see the need to make
their drain plugs accessible.
Date published: 2013-12-22
Rated 5 out of
5
by
Dennis Brown from
Drain
Installed in a minute, now can drain the tank without having to remove the plastic plug.
Date published: 2014-02-17
Rated 5 out of
5
by
PSU1 from
Works great!
Love it. Saves removing the plastic one which was all chewed up!
Date published: 2014-12-22
Q & A
Will this fit on an Atwood water heater?
Yes, Atwood uses a 1/2" drain plug on their water heater.
Date published: 2019-03-08
Are most hot water heater fittings the same size
There are two "standard" sizes, 1/2" and 3/8".
Date published: 2019-03-08